Finance | Project Operations, Human Resources, ...

Fixed Asset Depreciation value not correct

(6) Share

Report

Posted on by Faqruddin

1,909

Hi,

We run depreciation on a monthly basis in Dynamics 365 Finance. While running the depreciation proposal, I accidentally clicked the Cancel button. After that, when I tried to generate the depreciation journal again, the system started calculating depreciation with an incorrect credit amount of only 10 for all assets.

Could you please advise whether there are any temporary records or cache that need to be cleared?

Thank you.

Categories:

Dynamics 365 Finance

I have the same question (0)

All responses (8)

Answers (0)

Suggested answer

CA Aman Agrawal 123 on at

Like (2)

Report
Copy link

Link copied!

Hi,

The depreciation proposal only calculates and displays the depreciation and it does not post anything unless we post. So, if you have cancelled the same it will not have any impact on the Remaining depreciation, or depreciation amount to be calculated.

Please re check the Depreciation period remaining, scrap value in the Fixed asset book and is there any filter applied on the Records to include section in the Depreciation proposal form.

Regards,

Aman

Was this reply helpful? Yes No
Faqruddin 1,909 on at

Like (1)

Report
Copy link

Link copied!

Thank you for your response. Please find below details. I check for one fixed asset. The issue remain same.

Was this reply helpful? Yes No
Suggested answer

CA Aman Agrawal 123 on at

Like (3)

Report
Copy link

Link copied!

Hi,

You are running the depreciation on 31st Dec 25, which is the same date as Acquisition date and placed in service date, try running depreciation for 31st Jan 26, the amount will change.

Moreover verify the Minimum depreciation amount in the Fixed asset parameter, it should be 10. i.e., why you are getting the depreciation amount as 10.

Regards,

Aman

Was this reply helpful? Yes No
Suggested answer

Parthiv_Adhyaru 142 on at

Like (2)

Report
Copy link

Link copied!

Hi Faqruddin,

As Aman stated above, depreciation for all the assets are coming as 10 because of the FA parameter setup. We had a similar situation during cutover data migration and when we removed the default 10 value from FA parameter it started calculating the depreciation perfectly. give it a try and let us know if it solved your issue or not.

Thank you

Was this reply helpful? Yes No
Faqruddin 1,909 on at

Like (1)

Report
Copy link

Link copied!

Hi Aman,

I check for above asset the value is change for Jan. But we have strange situation in the system, system is not creating lines for all assets for depreciation proposal. I check one of the specific asset and try to create depreciation proposal, system is not creating entry completely. When generating the Depreciation Proposal for December, the system only reflects 750 assets and those 750 asset the depreciation value is correct, but total number of assets in the system we have 10000+ and system not created the entries for those assets.

Below one of the example System not created the entry. I pick randomly some assets to create depreciation but system not created any entry.

Was this reply helpful? Yes No
Suggested answer

Giorgio Bonacorsi 1,465 on at

Like (2)

Report
Copy link

Link copied!

Hello,

The depreciation proposal isn’t posting any entries, which means it has no impact on future proposals.
It’s probably not related to the proposal itself — something else is going on.
Try the following steps:

- Close all unused journals to clean up the situation.
- Open one asset that should be proposed for depreciation in D365FO, but isn’t appearing.

Most likely, the "last depreciation date" has been pushed forward for some reason.
If that’s the case:
- Check the existing transactions to understand what happened,
- or directly modify/adjust the last depreciation date if appropriate.

Thank you,
Giorgio

Was this reply helpful? Yes No
Faqruddin 1,909 on at

Like (0)

Report
Copy link

Link copied!

Hi,

I modify last depreciation date and created new depreciation proposal but still no lines created. Please also look below my Book profile.

Was this reply helpful? Yes No
Giorgio Bonacorsi 1,465 on at

Like (0)

Report
Copy link

Link copied!

Hello,

Could you please share the depreciation book configuration and your date/amount expectations?
From the profile, it looks like the system is calculating a depreciation amount.

Thank you,
Giorgio

Was this reply helpful? Yes No