web
You’re offline. This is a read only version of the page.
close
Skip to main content

Announcements

No record found.

News and Announcements icon
Community site session details

Community site session details

Session Id :
Dynamics 365 Community / Forums / Microsoft Dynamics AX (Archived) / New Module Parameter f...
Microsoft Dynamics AX (Archived)

New Module Parameter form for new number Sequence

(1) ShareShare
ReportReport
Posted on by Rohin 4,624

Hi All,

 i have created new module in AX and trying to setup number sequence for this module. So i have created Parameter table and respected parameter form .

 When i opened the parameter form and save number seq. reference there but it doesn't save number seq. reference when i open again the same form .

Please suggest ?

*This post is locked for comments

I have the same question (0)
  • Suggested answer
    Community Member Profile Picture
    Community Member on at

    Hi,

       The new module will store data related to existed module tables?

       For an example your using account receivable related data, Then you can use cust parameters table. same like if your using account payable related data, Then you can use vend parameters table. I thought there won't be a problem.

    Thanks

    Suresh

  • Rohin Profile Picture
    Rohin 4,624 on at

    No, it doesn't store data related to existing module.

     Like i said , My parameter form is for new Module (customized Module) .

    For instance , Structure of New parameter form :

    Parameter form : VehicleParameter

    DataSource : 1.  NumberSequnceReference

                          2.  VehicleParameters

    please suggest

  • Suggested answer
    Community Member Profile Picture
    Community Member on at

    Hi,

         What you took the scope parameters for this number sequence?

         Before creating number sequence , in which class you write the load module method?

         After that have you run the job to execute  NumberSeqApplicationModule::loadAll();  job to load your number sequence.

    Thanks

    Suresh

  • Rohin Profile Picture
    Rohin 4,624 on at

    I took dataArea Scope . I have created new numberSeqClass which extends NumberSeqApplicationModule class for this new module.

     I already run the job for loadAll number seq.

  • Rohin Profile Picture
    Rohin 4,624 on at

    I would like to share more information :

    Below is my parameter form:

    7380.1.PNG

    when i am trying to setup VehicleMakeId number seq setup through below form (by using View Details):

    7380.1.PNG

    This error comes when i am adding reference to this number seq in references fast tab.

    Please suggest

  • Verified answer
    Community Member Profile Picture
    Community Member on at

    Hi,

       Can you do one thing? Please re create number sequence NLI-VMI########. add check whether reference is showing your number sequence or not.

    Thanks

    Suresh

  • Verified answer
    Rohin Profile Picture
    Rohin 4,624 on at

    Hello Suresh ,

    I deleted VehicleMakeId number sequence and re created again but its not allow me to add reference and giving me the same error as shown above

    " Cannot create a record in Number sequence references (NumberSequenceReference). Datatype number sequence properties: 103964,      None.

    The record already exists."

    what is the  solution ?

  • Community Member Profile Picture
    Community Member on at

    Hi,

         If possible can you please explain what steps you followed to create this number sequence(VehicleMakeId). there will be some basic steps to create number sequence, so that i can determine where it is missing.

    Thanks

    Suresh

  • Rohin Profile Picture
    Rohin 4,624 on at

    Hi Suresh,

    I resolved this by generating number sequence using generate Wizard and now its generated successfully for VehicleMakeID for all companies and its shown below on parameter form:

    0181.10.PNG

    but when i used this number sequence in my form(customized form) then it gives below error while creating records:

    8510.4.PNG

    even i have used all required methods on this form as shown below :

    2234.5.PNG   0676.6.PNG

    4300.7.PNG     2642.8.PNG

    5466.9.PNG   0181.10.PNG

    please suggest what missing i am ?

  • Community Member Profile Picture
    Community Member on at

    Hi,

         Your first question is clear i think :)

         Where you are inserting the number sequence into table?

    Thanks

    Suresh

Under review

Thank you for your reply! To ensure a great experience for everyone, your content is awaiting approval by our Community Managers. Please check back later.

Helpful resources

Quick Links

Introducing the 2026 Season 1 community Super Users

Congratulations to our 2026 Super Stars!

Meet the Microsoft Dynamics 365 Contact Center Champions

We are thrilled to have these Champions in our Community!

Congratulations to the March Top 10 Community Leaders

These are the community rock stars!

Leaderboard > 🔒一 Microsoft Dynamics AX (Archived)

#1
Joris dG Profile Picture

Joris dG 5

#2
Alexey Lekanov Profile Picture

Alexey Lekanov 2

#2
Henrik Nordlöf Profile Picture

Henrik Nordlöf 2 User Group Leader

Last 30 days Overall leaderboard

Featured topics

Product updates

Dynamics 365 release plans