Skip to main content

Notifications

Announcements

No record found.

Microsoft Dynamics AX (Archived)

Change location profile to be non lp controlled

(0) ShareShare
ReportReport
Posted on by 1,230

hi

we have a location that was wrongly setup as an lp controlled Location profile

i have removed the stock from the location using std stock movement in wax, no transactions are open for the location, but when i try to change the location profile i get the message

Location profile cannot be changed to a location profile with a different licence plate tracking status if the location contains stock.


strange as the location definitely has zero stock but when i view on hand stock i can still see trace of the previous license plate in the location but with no physical stock

any ideas ? can the location profile change after it has been transacted on?

mr

*This post is locked for comments

  • Suggested answer
    raff Profile Picture
    raff 1,230 on at
    RE: Change location profile to be non lp controlled

    thank you Davut Dal

  • Verified answer
    davut Profile Picture
    davut 2 on at
    RE: Change location profile to be non lp controlled

    Hello Raff

    So you are not a developer you can check below link. I hope it will help you.

    [View:https://docs.microsoft.com/en-us/dynamicsax-2012/appuser-itpro/run-inventory-recalculation]

  • raff Profile Picture
    raff 1,230 on at
    RE: Change location profile to be non lp controlled

    ok apologies but i am not a developer, i see no reference to location in this table

    if the location has no stock, what am i looking for?

    what is Inventdimid referencing?

  • davut Profile Picture
    davut 2 on at
    RE: Change location profile to be non lp controlled

    when you try change location profile for wmsLocation Ax does check InventSum 

    if there is a record which InventoryDimension you try to change location and it is not closed yet you get error.

    https://community.dynamics.com/ax/b/galynafedorovaaxblog/archive/2016/11/17/inventsum-recalculation-for-specific-item check this link. and recalculate your item with this job.

    After running this job you will be able to change your location profile.

  • raff Profile Picture
    raff 1,230 on at
    RE: Change location profile to be non lp controlled

    hi Davut

    what does that mean from front end ax processing?

    mal

  • davut Profile Picture
    davut 2 on at
    RE: Change location profile to be non lp controlled

    Hello 

    check InventSum Table with inventDimId and ItemId

    Probably InventSum.Closed field is falsed.

    If you want to change location profile InventSım should be closed for this inventDimId.

  • raff Profile Picture
    raff 1,230 on at
    RE: Change location profile to be non lp controlled

    any ideas on this folks?

    we managed to make the location available again after running a month end process

    but if we have to flex pick face up in busy times, i wouldnt want to tell ops they must wait until  the end of the month!

    cheers

    m

Under review

Thank you for your reply! To ensure a great experience for everyone, your content is awaiting approval by our Community Managers. Please check back later.

Helpful resources

Quick Links

December Spotlight Star - Muhammad Affan

Congratulations to a top community star!

Top 10 leaders for November!

Congratulations to our November super stars!

Tips for Writing Effective Verified Answers

Best practices for providing successful forum answers ✍️

Leaderboard

#1
André Arnaud de Calavon Profile Picture

André Arnaud de Cal... 291,391 Super User 2024 Season 2

#2
Martin Dráb Profile Picture

Martin Dráb 230,445 Most Valuable Professional

#3
nmaenpaa Profile Picture

nmaenpaa 101,156

Leaderboard

Featured topics

Product updates

Dynamics 365 release plans